Once used MI 01 / W there was a DESCRAGA WAS THERE electricity and where my 01 / W ME IS THAT damaged NOS but as if someone took place Nusa could help pass the entire system again so as pasar por VIA MIDI from me TO THE 01 / W Many thanks for your attention.

None…

The instructions to reset to factory presets are in this message: http://launch.groups.yahoo.com/group/korg01w-list/message/6074

Excerpt:How to Re-Load All Combi/Prog/Kit Factory Settings
(from page 126 of the Percussion Manual
)
The steps below will re-install the factory settings. Note you can
re-load these settings at any time without re-initializing the entire
01/W 01/W> .
How to Re-Load All Combi/Prog/Kit Factory Settings 1 Press GLOBAL
to enter Global Mode. 2 Press “7″ to go to Page 7. 3 Select “Load
Combi/Prog” (on the top line). 4 Press G or H to execute the “LOAD”
command.
If you see the message “ERROR: Memory Protected”:
a. Press “4″ to go to Page 4.
b. Go to the bottom line (”Protect”).
c. Change the settings to show “Prog:OFF” and “Combi:OFF”.
To turn Prog OFF: Press button “A”, “B”, “C”, or “D”. Press VALUE
DOWN once.
To turn Combi OFF: Press button “E” or “F”. Press VALUE DOWN once.
d. Go to Step 2 above. 5 The 01 will ask “Are You Sure? Yes No”.
Notice that “yes” is positioned over buttons E and F. Pushing either
E or F means “yes”.
Notice that “no” is positioned over buttons G and H. Pushing either
G or H means “no”. 6 Push E or F. The message “Completed” should
appear.
Your 01 should now be as it came from the factory.

NOTE: This process disables the 01 from receiving System Exclusive MIDI
messages. To receive SysEx messages, go to GLOBAL Mode, Page 0, Line 6,
button F or G, and press VALUE UP one or more times to change EXCL from
DIS to ENA.
How to Re-Load a Factory Setting
Follow the steps below to re-install a single Combi, Prog, or Drum Kit
factory setting.
How to Re-Load a Factory Setting 1 Press GLOBAL to enter Global
Mode 2 Press “7″ to go to Page 7 3 Select the setting you want to
load. You can load a single Combi, Prog, or Drum Kit.
You can re-load everything, including Drum Kits, by selecting “Load
Combi/Prog” 4 For loading a single Combi/Prog/Kit:
Press A, B, or C to highlight the “source” side of the arrow.
Use the VALUE Slider/Buttons or Direct Entry to select the number of
the Combi/Prog/Kit you want to load from ROM. (for a list of ROM
contents, click here for Progs
or here for Combis
).
Press D, E, or F to highlight the “destination” side of the arrow.
Use the VALUE Slider/Buttons or Direct Entry to select the location
where you want to store the item in Active Memory. 5 Press G or H to
execute the “LOAD” command
If you see the message “ERROR: Memory Protected”:
a. Press “4″ to go to Page 4.
b. Go to the bottom line (”Protect”).
c. Change the setting to “Prog:OFF” or “Combi:OFF”, depending on which
you are trying to load.
To turn Prog OFF: Press button “A”, “B”, “C”, or “D”. Press VALUE
DOWN once.
To turn Combi OFF: Press button “E” or “F”. Press VALUE DOWN once.
d. Press “7″ to return to Page 7. Go to Step 3 above. 6 Your 01 will
ask “Are You Sure? Yes No”
You’ll notice that “yes” is positioned over buttons E and F. Pushing
either E or F means “yes”
You’ll notice that “no” is positioned over buttons G and H. Pushing
either G or H means “no” 7 Push E or F
Your 01 setting should now be in the destination you selected.

Hi. Long time no see. I recently re-kindled interest in my 01/W Pro and bought an 01R/W as a safety net in case the keyboard blows up.

My ROM versions are not the final version, #62. I looked around on the downloads section and couldn’t find a binary dump of the ROMs. If I remember right, a long time ago someone actually posted them to the group. Do you recall any of this?

Further, Ken Westover’s page says that he thinks that your site here might have the dumps:
Where to get EPROM Data
EPROM data may be available at http://www.vienxu.com/korg0 . File names for ROM #62 are reported to be 912162 and 912262, each 754,701 bytes big.

Maybe they had to be taken off of public display for some reason. If you’ve got a copy, could you kindly send it along? I would surely appreciate it.

Thanks,
Ed²

Also wondered if anyone knows if all the factory presets
will still be on the machine when I put a new batter in.

And if now, where would I get the presets? Korg?

Thanks in advance for your advise.

Scott Forman